1977–present

Williams

Source labelsWilliamsConstructors' titles9 (1980, 1981, 1986, 1987, 1992, 1993, 1994, 1996, 1997)
2026 carFW48
2026 Williams, 2026 Austrian Grand Prix, Friday practice
Photo: Lukas Raich, CC BY-SA 4.0 · background removed
Grands Prix869
Wins114
Podiums313
Titles9
The machine · 2026
Chassis
FW48
Power unit
Mercedes
Tyres
Pirelli
Team Principal
James Vowles
The powertrain · 2026

Mercedes power unit

Customer supply · Mercedes · Compare 2026 power units →

1.6 L V6 · 90°15,000 rpm maxMGU-K 350 kW max60,000 rpm max4 MJ usable window8 forward ratios

TURBOSingle turbocharger 1.6 L V615,000 rpm max GEARBOX8 forward ratios MGU-K350 kW max ENERGY STORE4 MJ usable window crank / drivetrain

Combustion

Displacement
1.6 L Manufacturer-published
Layout
V6 · 90° Manufacturer-published
Valves
24 (4 per cylinder) Manufacturer-published
ICE speed limit
15,000 rpm max Manufacturer-published
Fuel energy flow
3,000 MJ/h max FIA regulation

Turbo

Turbocharger
Single turbocharger Manufacturer-published
MGU-H
Removed for 2026 Manufacturer-published

Electric

MGU-K power
350 kW max Manufacturer-published
MGU-K speed
60,000 rpm max Manufacturer-published
Energy store
4 MJ usable window Manufacturer-published
Recovery limit
8.5 MJ per lap FIA regulation

Transmission

Gears
8 forward ratios FIA regulation

Fuel & fluids

Fuel
PETRONAS (Primax advanced sustainable fuel) Manufacturer-published
Lubricants
PETRONAS (Syntium engine oil, Tutela fluids) Manufacturer-published

Values are labelled by source: team-published, manufacturer-published, or FIA regulation (a 2026 limit, not a measured figure for this engine). Torque, boost pressure, gear ratios, operating rpm and thermal efficiency are not publicly disclosed.

Car Explorer · 2026

Select a part on the car of the FW48.

Front wing FW48

Car-specific

Detailed component specification not publicly disclosed.

General F1 tech · 2026 rules

  • The front wing carries two adjustable flaps (primary and secondary) that the FIA standard ECU switches between two fixed positions: Corner Mode (high downforce) and Straight Mode (reduced incidence, low drag).
  • Each switch between modes must complete within 400 ms, and any system failure must return the wing to Corner Mode.
  • The front wing flaps may only be deployed (Straight Mode) when the car is stationary or fully inside a designated Activation Zone.
  • The 2026 front wing is about 100 mm narrower than the 2022-25 design. Early FIA material called the modes 'Z-Mode'/'X-Mode'; the regulations now use Corner Mode / Straight Mode.

Design & engineering leadership

Pat Fry Chief Technical Officer · Matt Harman Technical Director of Engineering

Team-level technical leadership; not an attribution of this component to a named person.

Front tyre FW48

Car-specific

Detailed component specification not publicly disclosed.

General F1 tech · 2026 rules

  • Wheels stay 18-inch (rim diameter ~462.5-463 mm) and must be AZ70/AZ80 magnesium alloy; front rim tyre-mounting width is 315 mm.
  • Front tyres are 25 mm narrower than in 2022-25.

Tyres

Supplier
Pirelli
Generation
2026-generation narrower tyres on retained 18-inch wheels
Wheel rim
18-inch
Width
280 mm (-25 mm vs 2025)
Dry compounds
C1, C2, C3, C4, C5 · three nominated per event as Hard / Medium / Soft
Intermediate
One intermediate type: for wet track with no standing water or a drying surface
Full wet
One full wet (Extreme Wet) type for heavy rain
This weekend
2026 Bahrain Grand Prix in Malaysia: Hard C2 · Medium C3 · Soft C4

Stint and compound usage connect to PBEcast where our live timing data has them.

Brakes FW48

Car-specific

Detailed component specification not publicly disclosed.

General F1 tech · 2026 rules

  • One pedal feeds two master cylinders with separate front and rear hydraulic circuits.
  • Rear braking pressure may come from a powered brake-by-wire system run by the FIA control electronics, capped at 1.2x the driver's own rear pressure and backed by a hydraulic fallback.
  • Disc diameter is 325-345 mm at the front and 260-280 mm at the rear, max 34 mm thick; liquid cooling of brakes is forbidden.

Front suspension FW48

Car-specific

Detailed component specification not publicly disclosed.

General F1 tech · 2026 rules

  • Suspension must be passive: any powered device that changes suspension configuration is banned, and nothing may be adjusted while the car is moving.
  • Front and rear suspension must act independently, each responding only to loads on its own axle.
  • Push-rod vs pull-rod is a team choice; teams pick the layout for both mechanical and aerodynamic reasons.

Design & engineering leadership

Pat Fry Chief Technical Officer · Matt Harman Technical Director of Engineering

Team-level technical leadership; not an attribution of this component to a named person.

Cockpit / halo FW48

Car-specific

Detailed component specification not publicly disclosed.

General F1 tech · 2026 rules

  • Every car has two roll structures; the secondary one is the halo, built to FIA standard 8869-2018 by an FIA-designated manufacturer.
  • Roll hoop load requirement rose from 16G to 20G and side intrusion protection was strengthened for 2026.
  • Steering re-aligns only the two front wheels and must be a single steering wheel rotating about one axis.

Drivers & race engineers

Sidepod / cooling FW48

Car-specific

Detailed component specification not publicly disclosed.

General F1 tech · 2026 rules

  • Primary heat exchangers (radiators) must use aluminium alloy cores and header tanks and cannot be additively manufactured.
  • FIA introduced in-washing wheel-wake control boards at the front of the sidepods to manage front-wheel wake.

Design & engineering leadership

Pat Fry Chief Technical Officer · Matt Harman Technical Director of Engineering

Team-level technical leadership; not an attribution of this component to a named person.

Floor / underbody FW48

Car-specific

Published car weight
772.4 kg (incl. driver, excl. fuel), as reported from Williams' spec

General F1 tech · 2026 rules

  • 2026 cars use a partially flat floor and a less powerful diffuser, reducing ground-effect downforce and the need for ultra-stiff, low ride heights.
  • Maximum floor width was cut by 150 mm; a plank assembly with three measurement holes runs underneath.

Design & engineering leadership

Pat Fry Chief Technical Officer · Matt Harman Technical Director of Engineering

Team-level technical leadership; not an attribution of this component to a named person.

Power unit FW48

Car-specific

Detailed component specification not publicly disclosed.

General F1 tech · 2026 rules

  • The ICE remains a 1600 cc, 90 deg V6 with four valves per cylinder; fuel energy flow is capped at 3000 MJ/h.
  • The MGU-H is gone: only the engine and the MGU-K may propel the car or recharge energy. ERS-K power is capped at 350 kW (up from 120 kW).
  • FIA describes the power split as roughly 50/50: ICE about 400 kW plus 350 kW electric. Recharge is limited to 8.5 MJ per lap and the battery state-of-charge window to 4 MJ.
  • Fuel must be 100% advanced sustainable (from non-food biomass, municipal waste or renewable non-biological feedstock).

Mercedes power unit · customer supply (Mercedes)

TURBOSingle turbocharger 1.6 L V615,000 rpm max GEARBOX8 forward ratios MGU-K350 kW max ENERGY STORE4 MJ usable window crank / drivetrain

Combustion

Displacement
1.6 L Manufacturer-published
Layout
V6 · 90° Manufacturer-published
Valves
24 (4 per cylinder) Manufacturer-published
ICE speed limit
15,000 rpm max Manufacturer-published
Fuel energy flow
3,000 MJ/h max FIA regulation

Turbo

Turbocharger
Single turbocharger Manufacturer-published
MGU-H
Removed for 2026 Manufacturer-published

Electric

MGU-K power
350 kW max Manufacturer-published
MGU-K speed
60,000 rpm max Manufacturer-published
Energy store
4 MJ usable window Manufacturer-published
Recovery limit
8.5 MJ per lap FIA regulation

Transmission

Gears
8 forward ratios FIA regulation

Fuel & fluids

Fuel
PETRONAS (Primax advanced sustainable fuel) Manufacturer-published
Lubricants
PETRONAS (Syntium engine oil, Tutela fluids) Manufacturer-published

Power-unit leadership
Hywel Thomas Managing Director, Mercedes-AMG HPP

Full powertrain Compare power units

Rear suspension FW48

Car-specific

Detailed component specification not publicly disclosed.

General F1 tech · 2026 rules

  • Rear suspension is subject to the same passive-only rule: no powered devices and no in-motion adjustment.
  • The inboard parts (rockers, springs, dampers) count as sprung mass; uprights, links and wheels are unsprung.

Design & engineering leadership

Pat Fry Chief Technical Officer · Matt Harman Technical Director of Engineering

Team-level technical leadership; not an attribution of this component to a named person.

Rear tyre FW48

Car-specific

Detailed component specification not publicly disclosed.

General F1 tech · 2026 rules

  • Rear tyres are 30 mm narrower than in 2022-25; rear rim tyre-mounting width is 401.3 mm.
  • Tyre specification is set by the supplier with the FIA; teams may not cut, groove or chemically treat tyres.

Tyres

Supplier
Pirelli
Generation
2026-generation narrower tyres on retained 18-inch wheels
Wheel rim
18-inch
Width
375 mm (-30 mm vs 2025)
Dry compounds
C1, C2, C3, C4, C5 · three nominated per event as Hard / Medium / Soft
Intermediate
One intermediate type: for wet track with no standing water or a drying surface
Full wet
One full wet (Extreme Wet) type for heavy rain
This weekend
2026 Bahrain Grand Prix in Malaysia: Hard C2 · Medium C3 · Soft C4

Stint and compound usage connect to PBEcast where our live timing data has them.

Rear wing FW48

Car-specific

Detailed component specification not publicly disclosed.

General F1 tech · 2026 rules

  • The rear wing flap has two fixed, ECU-commanded positions - Corner Mode and Straight Mode - driven by a single actuator, replacing the old DRS concept.
  • Rear wing profiles are limited to at most three elements, and a failed adjuster must leave the flap in Corner Mode.

Design & engineering leadership

Pat Fry Chief Technical Officer · Matt Harman Technical Director of Engineering

Team-level technical leadership; not an attribution of this component to a named person.

2026 organisation

The people behind the machine

Driver → engineering → garage

#55Carlos SainzWilliams · 2026
  1. Race engineer · reportedGaetan Jego
  2. Performance engineerNot publicly verified
  3. Number one mechanicNot publicly verified
  4. Car crewIndividual roster not publicly verified

Ownership

  • Dorilton CapitalOwner · since 2020

Owners and shareholders as publicly recorded; job titles are not ownership.

Garage / mechanics

Named garage roles shown where the team documents them; individual mechanic roster otherwise not publicly disclosed.

All Williams people

Current 2026 roles from team, FIA and reputable motorsport sources; “reported” = confirmed by independent media, not yet by the team. Roles we cannot verify are left out; nobody is credited with designing a specific part.

Photo credits
◆ All Access · Race Lab

Unlock Williams intelligence

All Access opens Constructor DNA, the current teammate battle and deeper derived team analysis in Race Lab. Team history and season results remain free.

Season by season

PropBetEdge F1 Intelligence

Every lap
leaves a trace.

All Access opens Race Lab — full Circuit Fit, Driver DNA, form and teammate intelligence — plus the complete PBEcast timing tower, replay and position history across the PropBetEdge network.

PropBetEdge F1 Intelligence

Checking your PropBetEdge access…